BMW 3: Setting the speed
Maintaining and storing the speed
.png)
Press the rocker switch up or down once while the system is interrupted. The system will be activated.
The current speed is maintained and stored as desired speed.
The stored speed is displayed on the speedometer.
DSC Dynamic Stability Control is switched on, if necessary.
The speed can also be stored by pressing a button.
.png)
Press the button.
Changing the speed
.png)
Press the rocker switch up or down repeatedly until the desired speed is set.
If active, the displayed speed is stored and the vehicle reaches the stored speed when the road is clear.
- Each time the rocker switch is pressed to the resistance point, the desired speed increases or decreases by 1 mph/1 km/h.
- Each time the rocker switch is pressed past the resistance point, the desired speed changes by a maximum of 5 mph/10 km/h.
Hold the rocker switch in position to repeat the action.
Adjusting the distance
Safety information
Warning The system cannot serve as a substitute for the driver's personal judgment. Due to the system limits, braking can be late. There may be a risk of accident or risk of damage to property. Be aware to the traffic situation at all times. Adjust the distance to the traffic and weather conditions and maintain the prescribed safety distance, possibly by braking.
Reduce distance
.png)
Press the button repeatedly until
the
desired distance is set.
Instrument cluster will display selected distance.
Increase the distance
.png)
Press the button repeatedly until
the
desired distance is set.
Instrument cluster will display selected distance.
Continuing cruise control
An interrupted cruise control can be continued by calling up the stored speed.
Make sure that the difference between current speed and stored speed is not too large before calling up the stored speed. Otherwise, unintentional braking or accelerating may occur.
Press the following button on the steering wheel with the system interrupted:
.png)
Without steering and traffic jam
assistant.
.png)
With steering and traffic jam
assistant.
Cruise control is continued with the stored values.
In the following cases, the stored speed value is deleted and cannot be called up again:
- When the system is switched off.
- When drive-ready state is switched off.
Changing between cruise control with/without distance control
Safety information
Warning The system does not react to traffic driving ahead of you, but instead maintains the stored speed. There may be a risk of accident or risk of damage to property. Adjust the desired speed to the traffic conditions and brake as needed.
Switch mode of the cruise control
Switching cruise control without distance control off and on:
.png)
Press and hold this button..png)
Press and hold this button.
Without steering and traffic jam assistant: switch on distance control:
- Press the button.
- Press the button.
With steering and traffic jam assistant: switch on distance control:
.png)
Press the button.
After switching, a Check Control message is displayed.
READ NEXT:
Displays in the instrument
cluster
General information
Depending on the equipment version, the displays
in the instrument cluster may vary.
Display in the speedometer
Green marking: system is
active,
the marking indicates the
de
System limits
Detection range
The detection capacity of the system and the
automatic braking capacity are limited.
Two-wheeled vehicles for instance might not be
detected.
Deceleration
The system does not deceler
Speed Limit Assist
Concept
When the systems in the vehicle, e.g., Speed
Limit Info, detect a change of the speed limit
along the route, this new speed value can be applied
for the following systems:
Manual Speed Limit
SEE MORE:
With an emergency wheel:
enlarging the cargo area
Concept
The emergency wheel and any related components
can be temporarily removed to enlarge the
cargo area.
Removing the emergency wheel
and the storage compartments
1. To remove the cargo area floor, pull it upward
directly behind the rear backrests.
2. Remove tool holder and emergency wheel.
3.
Search criteria
General information
The possible search criteria depend on the selected
audio source.
Searching for track information
The following search criteria refer to the data
stored in the track information.
1. Move the Controller to the left.
2. "Media search".
3. Select the desired setting:
"Search"
